![]() ![]() Each fan is connected to control board with one plug.Īfter the miner is fully equipped and set up, the first thing you need to do is locate miner IP. Check whether the plug of fan cable has been fully or tightly connected. Network connection: plug in networking cable as follows.Ĥ. ![]() After pluging those cables, you need to double check if the cable is loose or not fully inserted.ģ. If errorly operated, hash board may encounter short circuit and damage. Just keep in mind to plug it in with right direction, namely the direction of buckle. Note: there's no difference in using which cable to connect with which interface. Cable connection of control board: there's one PCIe interface in control board and you just need to insert one 12V PSU cable. After plotted those cables, you need to double check if the cable is loose or not fully inserted.Ģ. Cable connection of hash board: Antminer S9 has three hash boards and each board has 3 PCIE intefaces, and each shall be connected with a 12V PSU cable, in total 9 pieces of 12V PSU cable. You can pin this button to reset the minerġ. The light flashes when the miner is working normally You can use IP Report software to get IP address of the miner by press this buttonĪlarm light flashes when the miner is in fault And don't worry about it.ī: a tool to locate miner IP, IP reporterĭ: pool website, visit and register an account Note: as computing boards are put in card slot chassis, you may hear some sounds by shaking the miner, which is a normal phenomenon. If yes, please take photos and contact customer service of miner producer Inspect from both the front and back fans to check whether heat sink is disconnected. If yes, please take photos and contact customer service of miner producer ģ. Please take miner out from package and then check whether there's deformation or damage in miner, fan, cable, fan cable etc. If yes, please take photos and contact customer service of miner producer Ģ. After receiving a new miner, please make a package inspection first to check whether the package or the miner inside is damaged. Tools needed: PSU, PSU power cable, miner, network cable, a personal computer for operationġ. Google or FireFox browsers are recommended to sign in miner backend.īefore setting up Bitmain Antminer S9, you need to make sure whether everything is ok and ready. Measures shall be taken to protect miners from dust, cax or so, otherwise hashrate board may be in corrosion and heat may fail to be dissipated ħ. Recommended operation temperature: 10-35 ☌ Ħ. ![]() Miners can only be connected to router or network switch with wired connection Ĥ. The router or network switch you are using to get connected with miners shall be ones without POE ģ. ![]() PSU output power is recommended to be 20% higher than the power consumption of miner Ģ. What You Need to Know before Using Miners:ġ. Here we will take Bitmain Antminer S9 as an example to introduce how to set up the miner and start to mine Bitcoin. For more details of miner hashrate, power consumption, Break-even point and so on, please visit Poolin website, *Screenshot taken on Jan. Now we can use the following miners to mine Bitcoin, including Bitmain Antminer S17, S15, T17, T15, S9, T9+., Whatsminer M20, M10, M3., Innosilicon T3, T2., AvalonMiner A921, A821, A741., Ebit E11, E9. Bitcoin uses SHA-256 algorithm and has a supply of 21 million, and current block reward is 6.25 BTC+Package transaction fee. On January 3rd, 2009, the first Bitcoin block was generated. On October 31st, 2008, Satoshi Nakamoto published a whitepaper named Bitcoin: A Peer-to-Peer Electronic Cash System. Bitcoin is the first decentralized peer-to-peer cryptocurrency and also the first successful application of blockchain technology. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |